top of page

Please note prices are subject to change (02.07.23)

Range Rover Classic, Discovery 1, Defender Cam Kit HP1041-42
HP1041-42 made by Kent Cams
All parts Made in USA, UK or European Union

Cam kit £449.99 incl. VAT @ 20%

Long nose cam kit HP1014-42

Click on the image

High Torque Cam Kit + 22 BHP over standard (3.5L - 5.0L) Carb/Efi or GEMS, Motronic 4.0/4.6

HP1041-42 made by Kent Cams

Suitable for 3.5, 3.9, 4.0, 4.2, 4.6, 4.8 & 5.0L + Rover/Buick V8 engines. Supplies enhanced performance on all motors over standard cam.

If the cylinder heads or block decks have not been extensively machined this cam should fit straight in.

Please advise if distributor fitted to engine.

KC Performance plus 22 BHP

Click on the image

Kent Performance High Torque P38 Range Rover & Discovery 2 Camshaft to suit 4.0/4.6 GEMS / MEMS Engines.

HP1041-42 made by Kent Cams

Suitable for 4.0/4.6L engine and derivatives using the serpentine timing cover assembly with GEMS or MEMS

High Torque Camshaft suitable for 4WD vehicles. Approx 16 - 18 BHP increase in power and similar increase in torque with these cams.

kent-cams-short-nose

Click on the image

Range Rover P38 GEMS or Thor High Torque Cam Kit
HP1041-42 made by Kent Cams
For Thor or GEMS engines.
RR P38 Thor image

Click on the image

Kent Cams Sports Torque H180 Hydraulic Cam suitable for automatics and off-road +22bhp
Applications V8 series 3.5, 3.9, 5.0L, Discovery 3.5, 5.0L, Range Rover 3.5, 3.9, 5.0L

Available as the cam only or in a range of cam kits.

£249.90 - £798.00 incl. VAT @ 20%

H180 Kent Camshaft long nose

Click on the image

VIPER CAMSHAFTS

DW270 Viper TYPHOON Hydraulic Camshaft and kits

Ideal for use with a Holley 390, stage 2 heads, Edelbrock or Offenhauser manifold, Rhoads, 1-1/2" headers, 9.75 compression pistons and a Mallory distributor.

From £191.30 - £648.99 incl. VAT @ 20%

Typhoon DW270 best.JPG

Click on the image

DW252 Viper Cyclone Hydraulic Camshaft and kits 3.9L Hot wire

Good for most applications including automatic transmission.

Worth an extra 26 hp over a standard engine.

Dyno tests + 26 bhp extra obtained at 5000 rpm with an extra

27 ft lbs of torque at the same rpm.

From: £191.30 - £500.03 incl. VAT @ 20%

Viper Cyclone DW252

Click on the image

DW268 Viper "Stump Puller" Hydraulic Camshaft for 3.9L and higher

Installed in a 4.0 litre engine, this cam gives 267 ft lbs of torque at 4000rpm.

From £205.54 including VAT

Stump Puller camshaft

Click on the image

Warranty

Camshaft and other Kent Cams products issues: if you think the camshaft you have purchased has a problem, it needs to be returned to us. We will then forward it to be inspected by Kent Cams and await their feedback before refunds can be issued. 

bottom of page